685.AZS-B
HSK Axial-Clamping Manual Grippers for Direct Installation
PDF Data Sheet: HSK Axial-Clamping Manual Grippers for Direct Installation (685.AZS-B)| HSK-A | HSK-B | Key Size | Torque | Force | Part Number | |||
|---|---|---|---|---|---|---|---|---|
| HSK-A/C/E 32 | HSK-B/D/F 40 | 4 | 3 Nm | 9 kN | 685.AZS.032.B00 | |||
| HSK-A/C/E 40 | HSK-B/D/F 50 | 4 | 6 Nm | 20 kN | 685.AZS.040.B00 | |||
| HSK-A/C/E 50 | HSK-B/D/F 63 | 5 | 10 Nm | 30 kN | 685.AZS.050.B00 | |||
| HSK-A/C/E 63 | HSK-B/D/F 80 | 6 | 12.5 Nm | 40 kN | 685.AZS.063.B00 | |||
| HSK-A/C/E 80 | HSK-B/D/F 100 | 8 | 18 Nm | 60 kN | 685.AZS.080.B00 | |||
| HSK-A/C/E 100 | HSK-B/D/F 125 | 8 | 25 Nm | 80 kN | 685.AZS.100.B00 |
For more information regarding this item (HSK Axial-Clamping Manual Grippers for Direct Installation) or other items, fill out the form below
or contact our office directly:
Telephone: 815-962-5600
Fax: 815-962-4600
Location: 304 North Main St, Suite 104, Rockford, IL 61101-1101 USA
Email: infο@ΤΑCRοckfοrd.cοm
Related
KS Installation Tools
Available for HSK-C 32, 40, 50, 63, 80, 100
HSK Axial-Clamping Manual Clamping Grippers
The Axial pliers Spanner is a manual HSK-tensioners with axially in the center lying indirect drive, which is accessible both from the front and from behind. It is particularly suitable for clamping of HSK, especially grinding wheel shots, with the AZS can be integrated into the hub of a wheel on the one hand, (HSK arranged vice versa - the spindle is the father) on the other hand, as usual, can be incorporated into the spindle using flange.
HSK-C 4 Point Manual Clamping Sets for Conventional Cooling
- For a coolant pressure up to 80 bar - Includes installation and operating instructions
KS Clamping Cartridges for Minimal Lubrication (MLC)
Available for HSK-C 40, 50, 63, 80, 100
HSK-C PowerClamp Manual Clamping Sets
- For coolant up to 80 bar - Includes installation and operating instructions - Includes threaded pin
HSK Hydraulic Self-Locking Clamping Systems
The self-limiting clamping system for HSK tools developed by BERG Spanntechnik is used in conjunction with the proven HSH clamping sets. In this solution the wedge drive itself is rigidly connected to the clamping set via a drawbar.
Mounting Nuts for HSK-A/C Interface Adaption
Can be mounted in front of the spindle shaft after the installation of the collet. Has the advantage of being adaptable to HSK-E or HSK-F tool interfaces in an HSK-A spindle. Just use the drive key to expand and then clamp the desired tool. The ENS slot nuts can also be used in manual clamping units for more flexibility. Available for HSK 32, 40, 50, 63, 80, and 100.
Clamping Cartridge Installation Tools
For the installation of 4-point clamping sets, if there are difficulties locking the spindle.
Submit your feedback