492.026.005.000
DIN55026-5, DIN55027-5, A1-5, A2-5, B1-5, B2-5 Lathe Spindle Face Ring
Full Data Sheet (492.020)
PDF Data Sheet: Lathe Spindle Face Ring (492.020)| Product | Gauge |
| Part Type | Lathe/Chuck Dimensional |
| Taper / Standard | DIN55026-5, DIN55027-5, A1-5, A2-5, B1-5, B2-5 |
| Size | 5 |
| d2 max. | 82.573 |
| d2 min. | 82.563 |
| Gauge | Ring |
| Standards | Size | d2 max. | d2 min. | Gauge | Part Number | |||
|---|---|---|---|---|---|---|---|---|
| DIN55026-3, DIN55027-3, A1-3, A2-3, B1-3, B2-3 | 3 | 53.983 | 53.975 | Ring | 492.026.003.000 | |||
| DIN55026-4, DIN55027-4, A1-4, A2-4, B1-4, B2-4 | 4 | 63.521 | 63.513 | Ring | 492.026.004.000 | |||
| DIN55026-5, DIN55027-5, A1-5, A2-5, B1-5, B2-5 | 5 | 82.573 | 82.563 | Ring | 492.026.005.000 | |||
| DIN55026-6, DIN55027-6, A1-6, A2-6, B1-6, B2-6 | 6 | 106.385 | 106.375 | Ring | 492.026.006.000 | |||
| DIN55026-8, DIN55027-8, A1-8, A2-8, B1-8, B2-8 | 8 | 139.731 | 139.719 | Ring | 492.026.008.000 | |||
| DIN55026-11, DIN55027-11, A1-11, A2-11, B1-11, B2-11 | 11 | 196.883 | 196.869 | Ring | 492.026.011.000 |
For more information regarding this item (DIN55026-5, DIN55027-5, A1-5, A2-5, B1-5, B2-5 Lathe Spindle Face Ring) or other items, fill out the form below
or contact our office directly:
Telephone: 815-962-5600
Fax: 815-962-4600
Location: 304 North Main St, Suite 104, Rockford, IL 61101-1101 USA
Email: infο@ΤΑCRοckfοrd.cοm
Related
Lathe Spindle Face Ring
Series 492.026 ring gauges are for lathe spindle face.
Lathe Spindle Face Ring With Indicator Mounts
Series 492.126 ring gauges are for lathe spindle face.
A2 Flanged Lathe Spindle Runout Test Bars
Test arbor for mounting to turning-center and measuring run-out. Designed for A2-5, A2-6, etc. lathe face mounting. Also available for flat 110 and 140 lathe face.
- Maximum runout error 0.003mm [0.00012 in.]
Drive Key Spindle Gauges
When inserted in the spindle, the "go" gauge should be in contact with the plane face. The "no go" gauge should not contact the face. Two measuring gauges in storage case: "go" and "no go" plug gauges.
Centro Setup Indicator
With the CENTRO, bores and shafts can be easily and precisely centered. The CENTRO is clamped into a tool holder and inserted into the spindle of the milling machine. The machine spindle is then positioned near the bore or shaft that is to be measured, and rotates at low speed.
KS Adapter Flanges with Angular Alignment
For fitting onto the machine spindle or on HSK or ISO adapters for holding HSK tools. Can be precisely set in radial run-out by using threaded pins (for alignment) on the machine spindle and on HSK or ISO adapters. Can be precisely set in face run-out using alignment screws (thrust pad and threaded pin) in the adapter flange. Available for HSK-C 32, 40, 50, 63, 80, 100.
Steep Taper Spindle Gauge Manual
Download PDF for instruction manual.
VDI Lathe Turret Alignment Bars
Lathe turret alignment bar for VDI interface. Used for both testing concentricity of the interface as well as center alignment and adjustment on a lathe. Made to DIN 69880 standard.
465.V50.59767 is a special configuration used on certain Mazak machines. Contact us for further information.
Contact us for other sizes or special requirements/configurations.
KS Adapter Flanges with Angular Alignment
Used for fitting onto machine spindle for holding HSK tools. Available for HSK-C 32, 40, 50, 63, 80, 100.
Submit your feedback