451.CG0.400.100

Granite Inspection Cylinders - 400 x 100

Granite Inspection Cylinder

Cylinder	H (mm)	D (mm)	Perpendicularity (mm)	Cylindricity (mm)	Part Number
200 x 70	200	70	0.002	0.002	451.CG0.200.070
300 x 80	300	80	0.003	0.003	451.CG0.300.080
400 x 100	400	100	0.004	0.004	451.CG0.400.100
500 x 120	500	120	0.005	0.005	451.CG0.500.120
800 x 160	800	160	0.006	0.006	451.CG0.800.160

For more information regarding this item (Granite Inspection Cylinders - 400 x 100) or other items, fill out the form below or contact our office directly:

Telephone: 815-962-5600
Fax: 815-962-4600
Location: 304 North Main St, Suite 104, Rockford, IL 61101-1101 USA
Email: infο@ΤΑCRοckfοrd.cοm

Add Comment		Alias
Full name
Position/Title
Company
Telephone
Fax
Email
Mailing Address

Receive a quote or more information on:

Questions or comments:

How did you hear about us?
Other:

Your preferred method of contact

Granite Inspection Cylinders

Master Granite Setup Squares (90 degrees)

<b>This product has been replaced by:</b>
<a href="https://tacrockford.com/product/gauges/machine-center-dimensional/granite-squares/">Granite Square Series 451.2G0</a>

Granite block with two diamond-lapped measuring faces. Made in Germany to DIN 875 / 876 standard.

Granite Squares

Granite Squares 4-Sided

HSK Tool Holder Taper Inspection Gauge

Designed to detect tool holder taper wear in seconds.

The tool holder taper inspection gauge includes two Fixture Bases, two 0.001mm Indicators, and a carrying case. An optional 410.148 certified Taper Master is strongly recommended for zeroing the Indicators. If a master is not available, a known good tool holder can be used in place of the master. Click the Details Tab for more information.

Tool Holder Taper Inspection Gauge

Available for all steep taper tool holder sizes (20, 30, 35, 40, 45, 50, 55, 60)

The tool holder inspection gauge is designed to inspect tool holder taper diameters for wear and other potential problems. Verifying tool holder tapers are correct can help to maximize spindle life and improve part finish.

Please note that the taper inspection gauge will only check diameter on two planes along with taper angle. The gauge will not detect nicks or localized damage to the taper. We recommend using series 430.110 taper sleeve gauges in conjunction with the taper inspection gauge for this purpose.

The tool holder taper inspection gauge includes the Fixture Base and two Indicators (0.002mm or 0.0001 inch resolution). An optional 430.110 certified Taper Master is strongly recommended for zeroing the Indicators. If a master is not available, a knowngood tool holder can be used in place of the master.

Spring Band Steel

We supply spring band steel either as pre-cut blanks or in coils with thickness values of 0.1 to 3.0 mm and widths of 2.0
- 120 mm. Available materials:
1.4310, 1.4301, C 75 S, C 100 S, CuSn6, CuZn37 as well as CuBe2

HDT Tool Clamping Cylinders

HDT pressure intensifiers are primarily designed for tool clamping and chucking systems using stationary hydraulic cylinders of the type HLZ for releasing the tool shanks when no hydraulic unit is available for operating them.

Precision Measuring Cylinders

Hardened special steel. Machined base and jacket surface.

Special Automotive Springs

Roehrs automotive exhaust system springs are designed for use between the engine and exhaust system. They utilize a fully elastic suspension to minimize bending stress, and are designed for absorption of axial forces and torsion at temperatures up to 400 °C. The springs minimize noise and help to extend the lifetime of the exhaust system since they are constructed of corrosion resistant materials.