492.126.015.000
Lathe Spindle Face Ring With Indicator Mounts - A2-15
Full Data Sheet (492.126)
PDF Data Sheet: Lathe Spindle Face Ring With Indicator Mounts (492.126)| Lathe Spindle Face Ring | Part Number | |||||||
|---|---|---|---|---|---|---|---|---|
| A2-3 | 492.126.003.000 | |||||||
| A2-4 | 492.126.004.000 | |||||||
| A2-5 | 492.126.005.000 | |||||||
| A2-6 | 492.126.006.000 | |||||||
| A2-8 | 492.126.008.000 | |||||||
| A2-11 | 492.126.011.000 | |||||||
| A2-15 | 492.126.015.000 |
For more information regarding this item (Lathe Spindle Face Ring With Indicator Mounts - A2-15) or other items, fill out the form below
or contact our office directly:
Telephone: 815-962-5600
Fax: 815-962-4600
Location: 304 North Main St, Suite 104, Rockford, IL 61101-1101 USA
Email: infο@ΤΑCRοckfοrd.cοm
Related
Lathe Spindle Face Ring With Indicator Mounts
Series 492.126 ring gauges are for lathe spindle face.
Lathe Spindle Face Ring
Series 492.026 ring gauges are for lathe spindle face.
A2 and D1 Flanged Lathe Spindle Runout Test Bars
Test arbor for mounting to turning-center and measuring run-out. Designed for A2-5, A2-6, D1-8 etc. lathe face mounting. Also available for flat 110 and 140 lathe face.
- Maximum runout error 0.003mm [0.00012 in.]
HSK Dial Indicator Spindle Taper Gauge Manual
Instruction manual for the dial indicator spindle taper gauge (410.310)
Centro Setup Indicator
With the CENTRO, bores and shafts can be easily and precisely centered. The CENTRO is clamped into a tool holder and inserted into the spindle of the milling machine. The machine spindle is then positioned near the bore or shaft that is to be measured, and rotates at low speed.
Tool Holder Taper Complete Measuring Units
Calibrated with a gauge master, the taper gauge checks large taper diameter, small taper diameter, straightness of the taper, relationship of the flange to the taper, and taper length.
Electronic Tool Taper Gauges
The four transducers mounted in the measuring ring are used for differential measurement of gauge dimensions d2 and d3. Deviations from the calibrated taper plug gauge are shown on the two indicator columns.
Dial Indicator Spindle Taper Gauges
To ensure sustained accuracy at HSK interfaces, we recommend comparison measuring of the geometry of HSK tool shanks and spindles at regular intervals. These checks should become more frequent with an increased change rate at the interface. Calibration on request.
Steep Taper Spindle Taper Dial Indicator Gauge
TAC Rockford's steep taper spindle gauge is designed to verify and measure correct location of the spindle gauge line.
Not included are an indicator and taper master.
The gauge can be used with any dial indicator with an 8mm stem. Recommended available options:
Part Nr. 499.220.150
- 0.01mm Resolution
Part Nr. 499.220.151
- 0.001mm Resolution
Part Nr. 499.220.155
- 0.00005" Resolution
In addition, we strongly recommend a 430.110 series Taper Sleeve Gauge to zero the indicator.
Taper Plug Gauges With Indicator Mounts
Taper gauges can be custom-manufactured to customer specifications. Hard chrome-plate and tungsten carbide gauges also available.
Cases are not included. Contact us for high quality gauge crib and travel case options.
Submit your feedback